Bonato electrostatic
The FH-4P fixing heads have been designed to be installed in tight spaces.
The stainless steel emitters are connected through high voltage resistors, which prevent the creation of sparks and at the same time are safer for the operator.
The FH-4P and CP-01 fixing head has been designed to lay down cast film borders in production lines, thus preventing film from reducing its length, in labelling and other sectors.
The stainless steel emitters are connected to high voltage by means of resistors and impede sparks creation, while being safer for the operator.
EFE-3 edges fixer has been designed to lay down cast film borders in production lines, thus preventing film from reducing its length.
The adjustable and interchangeable stainless steel emitters are connected to high voltage by means of resistors and impede sparks creation, while being safer for the operator.
CBR-LP-15 low profile electrostatically charging bars are designed to make a material adhere to a surface or two materials between them. These charging bars are connected to a generator, which creates (positive or negative) ions on bar’s pointed edges by means of high voltage. Thus the material, passing through the bar and a reference mass, is pushed towards the mass itself, creating a temporary adhesion.
CBR-05 electrostatically charging bars are designed to make a material adhere to a surface or two materials between them. These charging bars are connected to a generator, which creates (positive or negative) ions on bar’s pointed edges by means of high voltage. Thus the material, passing through the bar and a reference mass, is pushed towards the mass itself, creating a temporary adhesion.
CBR-10 electrostatically charging bars are designed to make a material adhere to a surface or two materials between them. These charging bars are connected to a generator, which creates (positive or negative) ions on bar’s pointed edges by means of high voltage. Thus the material, passing through the bar and a reference mass, is pushed towards the mass itself, creating a temporary adhesion.
ECG50 charge generator creates an adjustable high voltage between 5 to 50 KV and an also adjustable current between 0 and 2,5 mA. Its controls are very intuitive and thus easy to be used by the operator. Besides it can be remotely controlled by means of the remote control analogical function. It can have positive or negative charge on request and from 1 to 4 high voltage outputs
ECG40 charge generator creates an adjustable high voltage between 0 to 40 KV and an also adjustable current between 0 and 5 mA. Its controls are very intuitive and thus easy to be used by the operator. Besides it can be remotely controlled by means of the remote control analogical function. It can have positive or negative charge on request and from 1 to 4 high voltage outputs
ECG30 charge generator creates an adjustable high voltage between 0 to 30 KV and an also adjustable current between 0 and 5 mA. Its controls are very intuitive and thus easy to be used by the operator. Besides it can be remotely controlled by means of the remote control analogical function. It can have positive or negative charge on request and from 1 to 4 high voltage outputs
The antistatic tube has been developed to remove antistatic charges from materials carried by pneumatic systems.
Installing the antistatic tube you have no more clogging due to accumulation of electrostatically charged materials, thus reducing machine downtimes considerably.
Antistatic bar for a flat nozzle contains 4 ionizing pins. When compressed air flows from the thin slot of the flat nozzle, volume is amplified by the ambient air. That compressed air pick up the ions (without unwanted discharging) and directs them on the surface of products.
Bonato Antistatic Bar – IH-4-AN
The antistatic nozzle IH-4-AN is composed of a compressed air nozzle and a small antistatic bar with 4 pins. The ionizing pins are shockless. The compressed air pick up the ions and directs them on the surface of products to be discharge.
Bonato electrostatic Antistatic Bar – IH-4
The ionizing head IH-4 is a small antistatic bar. All its electronic components are impregnated in epoxy resin so as to ensure safety and durability. The stainless steel emitters are shockless as they are connected to the high voltage through resistors.
Bonato electrostatic Ionizing Blower – IF-AC
The ionizing blower IF-AC was developed to be effective at long range and to eliminate antistatic charges considerably.
The ionizing blower IF-AC is made up of axial fans (one every 250 mm) and 2 antistatic bars ABSL-RC, which are fed by a high-voltage power supply, integrated in the blower itself.
Bonato electrostatic Ionizing Blower – IB-600
The ionizing blower IB-600 is suitable for applications where it is necessary to have a strong air
flow or where ionizing point is hard to reach.
Bonato electrostatic Ionizing nozzles – AN-01
Like other active anti-static equipment, also ionizing nozzles must be connected to an anti-static power supply by means of a high-tension cable and to compressed air via a common 6 mm air hose. We recommend the use of an air filter in such a way as to prevent the nozzle from coming into contact with impurities and moisture.
Bonato electrostatic Ionizing point – IP-01
Ionizing nozzles are employed where installation conditions are critical, especially in confined spaces.
These nozzles has a pvc core, where all its electronic components are impregnated in epoxy resin so as to ensure safety and durability.
Bonato electrostatic Ionizing Gun – AG-03
The AG-03 antistatic gun is flat air nozzle with small ionizing bar. The ionizing pin is shockless. When compressed air flows from the thin slot of the flat nozzle, volume is amplified by the ambient air. That compressed air pick up the ions (without unwanted discharging) and directs them on the surface of products.
Bonato electrostatic Ionizing Gun – AG-02
The AG-02 antistatic gun is a transvector compressed air gun that removes static charge. The ionization pin is of the “shockless” type – without danger when touched. In addition, the pin is protected in a robust gun body.
Bonato electrostatic Ionizing Gun – AG-01
The antistatic gun AG-01, shockless, is a compressed air gun with a ions emitter nozzle. This allows that the air flow becomes ionized when you push the trigger and so able to eliminate the electrostatic charges, which are present on the surfaces where the trigger is directed. With this design the antistatic gun AG-01 is very effective in comparison with guns with internal ionization as well as very maneuverable and ergonimic. The gun AG-01 is supplied with a high voltage cable, which is available in different lenghts and which has to be connected to a power supply.
Bonato electrostatic Power-Supply – AF4WR
The AF4WR power can feed up to 4 antistatic devices, has external Jack connec-tors, is mounted in a painted metal box, with ON / OFF control switch, signal lamp in service and thermal circuit breaker for protection in case of faults of the secondary one.
Bonato electrostatic Power supply AF2WR
The AF2WR power can feed up to 2 antistatic devices, has external Jack connec-tors, is mounted in a painted metal box, with ON / OFF control switch, signal lamp in service and thermal circuit breaker for protection in case of faults of the secondary one.
Bonato electrostatic Antistatic Bar – ABSL-RC-T
The antistatic bar ABSL-RC-T i san antistatic bar coupled with a motorie air knife. By using blowers in stead of compressed air, the blower driven airknife can reduce operational costs by 60% to 90%. The motorized air knives coupled with an antistatic bar are ideal for cleaning and neutralization of electrostatic charges both on flat surfaces that wavy.
Bonato electrostatic Antistatic Bar – ABSL-RC-DE
The antistatic bars ABSL -RC-DE (shockless), can be used in many sectors, such as textile manufacturing, paper, plastics, printing, in converting, packaging etc.
The anti-static bar ABSL –RC-DE was designed to connect more antistatic bars in a series using a single cable from the power supply. IT can be installed in machines working at high speed, it is very effective in the removal of electrostatic charges.
Bonato electrostatic Antistatic Bar – ABSL-RC-AKM
The antistatic bar ABSL-RC-AKM is an antistatic bar coupled with an air knife. The air knife is an amplifier of air flow, in effect it amplifies the compressed air flow used from 30 to 40 times, in this way you have a big energy savings in electricity terms for compress air.
Bonato electrostatic Antistatic Bar – ABSL-RC-S
The antistatic bars ABSL – RC (shockless), can be used in many sectors, such as textile manufacturing, paper, plastics, printing, in converting, packaging etc.
The anti-static bar ABSL – RC is designed to be installed in machines working at high speed, it is very effective in the removal of electrostatic charges.
Bonato electrostatic Antistatic Bar – ABS
Antistatic antishock bar with a PVC core covered in painted aluminium. Antistatic bars can be used universally in many applications. The antistatic bars can be customized to suit specific applications. When choosing the bar size, ensure that the height of the material to dielectrify is slightly less or equal to length LF.
Bonato electrostatic Antistatic Bar – ABSL
Antistatic antishock bar with a PVC core covered in painted aluminium. Antistatic bars can be used universally in many applications. Our antistatic bars can be customised to suit specific applications.
Bonato electrostatic Antistatic Bar – ABSL-RC
The antistatic bars ABSL – RC (shockless), can be used in many sectors, such as textile manufacturing, paper, plastics, printing, in converting, packaging etc. The anti-static bar ABSL – RC is designed to be installed in machines working at high speed, it is very effective in the removal of electrostatic charges.
Bonato electrostatic Antistatic Bar – EX-ABSL-RC
The anti-static bar EX-ABSL – RC is designed to be installed in machines working at high speed, it is very effective in the removal of electrostatic charges.
This anti-static bar has a pvc core, where all its electronic components are impregnated in epoxy resin so as to ensure safety and durability. It is coated with aluminum, with stainless steel emitters.
Bonato electrostatic Antistatic Bar – IDB-11 (24 VDC)
The Intelligent Discharging Bar IDB-11 (shockless), can be used in many sectors, such as textile manufacturing, paper, plastics, printing, in converting, packaging etc.
The anti-static bar IDB-11 is available in two versions: IDB-11-S for high speed up to 2000 m/min., for distance from 30 to 200mm and IDB-11-L for long distance from 150 up to 500 mm. His design is very compact 40×25 mm and the profile is in FR-ABS filled with epoxy resin.
Bonato electrostatic Antistatic bar – IDB-7 (24 VDC)
The Intelligent Discharging Bar IDB-7 (shockless) we produce can be used in many sectors, such as textile manufacturing, paper, plastics, printing, in converting, packaging etc. The anti-static bar IDB-7 is designed to be installed in machines working at high speed, his design is very compact 40×25 mm and the profile is in FR-ABS filled with epoxy resin.
Bonato electrostatic Antistatic Brushes SAR-01
The brush bristles are really soft and thin in order not to damage the material with they have contact with. The antistatic brushes do not have to be against the material to discharge, but if the static charge is not high they can be mounted to a distance of 2-5 mm.